Get the Pass

Connecticut permit test: signals and pavement markings

A red light means stop. You may turn right on red after a full stop if no sign bans it and no traffic or pedestrian is in the way. A yellow light means the light is about to turn red. Stop if it is safe, but if you are already in the intersection, continue through. A flashing red light is the same as a stop sign. A flashing yellow light means slow down and use caution. A red arrow means stop and do not go that way. If a traffic light is out, stop as if the intersection had a stop sign. A HAWK signal is a pedestrian signal with two red lights over one yellow. When it shows solid red, you must stop. Dashed yellow lines allow passing. A dashed yellow line next to a solid yellow line allows passing only on the dashed side. Double solid yellow lines mean no passing, but you may cross them to turn left into a driveway or alley. A double solid white line prohibits lane changes.

Handbook: Reading the Road – Pavement Markings; Traffic Lights and Signals

7 practice questions

1. What does a flashing red traffic light mean?
  1. Slow down and proceed with caution through the intersection
  2. Stop fully, then go when it is safe
  3. Stop and wait for a green light
  4. Yield only if cross traffic is present
Show answer

Answer: B. Stop fully, then go when it is safe

A flashing red light means the same as a stop sign. You must stop fully and may proceed when it is safe.

Handbook: Reading the Road – Traffic Lights and Signals

2. A traffic light is out at an intersection because of a power failure. What must you do?
  1. Slow down and proceed without stopping
  2. Treat it as a yield sign
  3. Stop as if there were a stop sign
  4. Follow the vehicle ahead of you through the intersection
Show answer

Answer: C. Stop as if there were a stop sign

Connecticut law requires a driver at an intersection with an inoperative stop light to stop as though a stop sign controlled it.

Handbook: Hazardous Conditions – Stop Light Not Working

3. A solid yellow line runs next to a dashed yellow line in the center of the road. When may you pass?
  1. Only when the solid line is on your side
  2. Never, because the road has a yellow line
  3. Always, if you can see that no traffic is oncoming
  4. Only if the dashed line is on your side
Show answer

Answer: D. Only if the dashed line is on your side

Passing is allowed on the side of the broken line but not on the side of the solid line, and only when it is safe.

Handbook: Reading the Road – Pavement Markings

4. You are already in the intersection when a green light turns yellow. What should you do?
  1. Stop where you are, in the middle of the intersection
  2. Back up behind the stop line before the light changes
  3. Back up behind the stop line
  4. Speed up and sound your horn as you cross it
Show answer

Answer: A. Stop where you are, in the middle of the intersection

A yellow light means the light is about to turn red. If you are already in the intersection, do not stop. Continue through.

Handbook: Reading the Road – Traffic Lights and Signals: Yellow

5. What does a red arrow mean?
  1. You may turn in that direction if you use caution as you go
  2. You must stop and may not go in the arrow's direction
  3. You may go after you yield to the other traffic around you
  4. The protection of a green arrow is ending and you should speed up
Show answer

Answer: B. You must stop and may not go in the arrow's direction

You may proceed only when the red arrow goes out and a green arrow or light comes on. A yellow arrow is the one that signals the end of protection.

Handbook: Reading the Road – Traffic Lights and Signals: Arrows

6. A HAWK pedestrian signal shows solid red. What must drivers do?
  1. Slow down and drive on through the crossing with some care
  2. Stop only if a pedestrian is walking in your own lane of travel
  3. Stop, because pedestrians are in the crosswalk
  4. Proceed, because the signal is dark and the crossing is turned off
Show answer

Answer: C. Stop, because pedestrians are in the crosswalk

A solid red means pedestrians are in the crosswalk and drivers must stop. A dark HAWK signal has not been activated, so vehicles may proceed.

Handbook: Reading the Road – Traffic Lights and Signals: HAWK Signals

7. What does a double solid white line on the pavement mean?
  1. Passing is allowed with care
  2. The lane is for buses only
  3. A school zone starts here
  4. Lane changing is prohibited
Show answer

Answer: D. Lane changing is prohibited

A double solid white line prohibits lane changing. A single solid white line also tells you to stay in your lane unless a special situation requires a change.

Handbook: Reading the Road – Pavement Markings: Other Markings