Get the Pass

Oklahoma permit test: signals and pavement markings

A steady green light means go when the intersection is clear. A steady yellow light means stop if you can do so safely before the crosswalk. A red light means stop before the crosswalk, and you may turn right on red after a complete stop unless a sign forbids it. You may also turn left from a one-way street onto a one-way street after stopping. A flashing red light means the same as a stop sign. A flashing yellow light means slow down and watch for cross traffic. A flashing yellow arrow lets you turn left after yielding to oncoming traffic and pedestrians. A flashing red arrow bans turns in the arrow direction until a green signal. A flashing Don't Walk signal means do not leave the curb. Pavement lines: broken yellow lines allow passing when safe. A solid yellow line in your lane means do not pass. White lines separate traffic going the same way. On three-lane roads the center lane is for left turns only. A red X above a lane means do not use it.

Handbook: Chapter 4: Signs, Signals and Markings; Chapter 6

8 practice questions

1. You are approaching an intersection and the light turns steady yellow. What should you do?
  1. Speed up to clear the intersection before the light turns red
  2. Stop if you can do so safely before the crosswalk
  3. Always stop immediately, even in the intersection
  4. Treat it as a green light for turning only
Show answer

Answer: B. Stop if you can do so safely before the crosswalk

A steady yellow light warns that the light is about to turn red. You must stop if you can stop safely before entering the crosswalk. Do not speed up to beat the light.

Handbook: Chapter 4: Signs, Signals and Markings – Traffic Signals

2. What does a flashing red light mean?
  1. Slow down and proceed with caution, but do not come to a stop
  2. The signal is broken and traffic may go
  3. Stop only if cross traffic is present
  4. The same as a stop sign: stop, then go when it is safe
Show answer

Answer: D. The same as a stop sign: stop, then go when it is safe

A flashing red light is used at dangerous intersections and means the same as a stop sign. You must stop and may go only when it is safe to cross.

Handbook: Chapter 4: Signs, Signals and Markings – Traffic Signals

3. What must you do at a flashing yellow arrow for a left turn?
  1. Turn at once, because a flashing arrow gives you the right-of-way over all traffic
  2. Yield to oncoming traffic and pedestrians, then turn when safe
  3. Stop and wait for a green arrow
  4. Turn only if there is no crosswalk
Show answer

Answer: B. Yield to oncoming traffic and pedestrians, then turn when safe

At a flashing yellow arrow, reduce speed and turn only after yielding. Oncoming traffic has the right-of-way. A flashing yellow arrow does not give you a protected turn.

Handbook: Chapter 4: Signs, Signals and Markings – Traffic Signals

4. When may you turn right at a red light in Oklahoma?
  1. After a complete stop, unless a sign forbids it, yielding to others
  2. Never in Oklahoma; a red light always means you must wait for the green light
  3. Only after slowing down, without stopping
  4. Only when no sign is posted and you honk first
Show answer

Answer: A. After a complete stop, unless a sign forbids it, yielding to others

After you come to a complete stop, you may turn right on red unless signs forbid it. You must yield to all pedestrians and vehicles, including bicycles. A rolling turn is not a complete stop.

Handbook: Chapter 4: Signs, Signals and Markings – Traffic Signals (Red Light)

5. A solid yellow line is on your side of the center of a two-way road. What does it mean?
  1. You may pass if the road ahead is clear
  2. You may pass only on hills
  3. You must not pass
  4. The road is one-way
Show answer

Answer: C. You must not pass

A solid yellow line in your lane means do not pass. You may cross it only to turn left. A broken yellow line is the one that permits passing when it is safe.

Handbook: Chapter 4: Signs, Signals and Markings – Pavement Markings; Chapter 6 – Lane Usage

6. What do white dashed lines between lanes show?
  1. Traffic moves in opposite directions, and passing is allowed only when safe
  2. Traffic goes the same direction on both sides; passing is allowed when safe
  3. Passing is never allowed
  4. The lane is for turning only
Show answer

Answer: B. Traffic goes the same direction on both sides; passing is allowed when safe

White lines separate traffic that goes the same direction. Dashes mean you may change lanes or pass when it is safe. Yellow lines are the ones that separate opposite directions.

Handbook: Chapter 6: Lane Usage and Maneuvers – Lane markings

7. A red X appears over your lane on a lane control signal. What does it mean?
  1. Use the lane only to turn left
  2. Do not use that lane
  3. Slow down and merge left
  4. The lane is open to all traffic
Show answer

Answer: B. Do not use that lane

A red X means the lane is closed to you. A green arrow means the lane is open to traffic.

Handbook: Chapter 4: Signs, Signals and Markings – Lane Control Signals

8. A pedestrian signal is flashing "Don't Walk" and you are a pedestrian still at the curb. What should you do?
  1. Start across quickly before it turns solid
  2. Do not leave the curb
  3. Cross if no cars are moving
  4. Wait only if the traffic light is red
Show answer

Answer: B. Do not leave the curb

A flashing Don't Walk signal means do not leave the curb, but continue if you are already in the intersection. Drivers should watch for people who started before the flashing began.

Handbook: Chapter 4: Signs, Signals and Markings – Pedestrian Signals