Get the Pass

Wisconsin permit test: signals and pavement markings

A steady red light means stop. You may turn right on red after a full stop if no sign forbids it. You may turn left on red only from a one-way street onto a one-way street. A flashing red light also means stop, then go when it is safe. A steady yellow light means the light will turn red. Stop before the intersection, but if you are already in it, keep going. A flashing yellow light means slow down and proceed with caution. A steady green arrow lets you turn in that direction with no oncoming or crossing traffic. If a signal has no power, treat it as a stop sign. A solid white line between lanes means do not cross, except for a hazard or a turn within the next block. A dashed white line lets you change lanes when safe. Two solid yellow lines mean no passing. A dashed yellow line on your side of a solid line lets you pass when safe. Stop with your front wheels just before the solid white crosswalk line. In a reversible lane, a red X means closed and a green arrow means open.

Handbook: Section 5: Signals, Pavement Markings and Lane Controls

8 practice questions

1. A traffic signal is dark because the power is out. What should you do?
  1. Proceed as if the signal were a stop sign
  2. Go straight through without slowing down
  3. Wait there until the power returns
  4. Treat it as if it were a flashing yellow light
Show answer

Answer: A. Proceed as if the signal were a stop sign

The handbook says to treat a signal that loses power or fails as a stop sign. Follow any police officer who directs traffic.

Handbook: Section 5: Signals, Pavement Markings and Lane Controls.A Traffic Signals

2. What does a flashing yellow light mean?
  1. Slow down and proceed with caution
  2. Come to a full stop and then go
  3. The light is about to change to red
  4. Do not enter the intersection
Show answer

Answer: A. Slow down and proceed with caution

A flashing yellow light tells you to slow down, check cross traffic and proceed with care. A flashing red light is the one that requires a full stop.

Handbook: Section 5: Signals, Pavement Markings and Lane Controls.A Traffic Signals

3. When may you turn left on a red light in Wisconsin?
  1. Any time there is no traffic
  2. Only when you are in the left-most lane of a two-way street
  3. When you turn from a one-way street onto a one-way street
  4. Never, in any case
Show answer

Answer: C. When you turn from a one-way street onto a one-way street

The handbook allows a left turn on red only from a one-way street onto a one-way street. You must stop and yield first.

Handbook: Section 5: Signals, Pavement Markings and Lane Controls.A Traffic Signals

4. You are in the intersection when the light turns steady yellow. What should you do?
  1. Stop right where you are in it
  2. Continue through the intersection
  3. Back up to a spot behind the line
  4. Honk and then stop in the middle
Show answer

Answer: B. Continue through the intersection

If you are already in the intersection when yellow comes on, do not stop. If you are not yet in it, slow down and stop.

Handbook: Section 5: Signals, Pavement Markings and Lane Controls.A Traffic Signals

5. What do two solid yellow lines in the center of the road mean?
  1. You may pass if the road is clear
  2. No lane of travel can pass
  3. Only the left lane may pass
  4. Passing is allowed in daylight only
Show answer

Answer: B. No lane of travel can pass

Two solid yellow lines mean no one may pass. The exceptions are turning into a driveway and passing a slow vehicle going less than half the speed limit, but not farm equipment.

Handbook: Section 5: Signals, Pavement Markings and Lane Controls.B Types of Line Markings

6. A dashed yellow line is on your side of a solid yellow line. May you pass?
  1. No, because a solid line is present nearby
  2. Yes, when it is safe, because you are on the dashed side
  3. Yes, but only at night when the road is clear
  4. No, unless a posted sign says that you may
Show answer

Answer: B. Yes, when it is safe, because you are on the dashed side

With a dashed and a solid yellow line, you may pass if you are on the dashed side. The driver on the solid side may not pass.

Handbook: Section 5: Signals, Pavement Markings and Lane Controls.B Types of Line Markings

7. What does a solid white line between two lanes going the same way mean?
  1. You may cross it at any time at all
  2. It splits traffic going in opposite ways
  3. It marks the center of a two-way road
  4. Do not cross, except for a hazard or turn
Show answer

Answer: D. Do not cross, except for a hazard or turn

A solid white line between lanes means you cannot cross. You may cross only for a hazard or to turn within the next block.

Handbook: Section 5: Signals, Pavement Markings and Lane Controls.B Types of Line Markings

8. At a crosswalk marked with a solid white line, where should your front wheels stop?
  1. On the crosswalk, beside the pedestrians
  2. Just before the solid white line
  3. Past the crosswalk, in the intersection
  4. Anywhere that is behind the nearest car
Show answer

Answer: B. Just before the solid white line

Your front wheels should stop just before the solid white line. Do not stop on the crosswalk.

Handbook: Section 5: Signals, Pavement Markings and Lane Controls.B Types of Line Markings