Get the Pass

Oregon permit test: signals and pavement markings

A dark signal is a stop sign in all directions. A flashing red signal also means stop. A steady red means stop until it changes. On red, after a full stop, you may turn right onto a two-way road, or turn right or left onto a one-way road in the direction of traffic, unless a sign or officer says no. A left turn on red from a one-way road onto a two-way road is not allowed. A steady yellow warns that red is coming. Stop if you can do so safely. A flashing yellow means slow down and use caution. A flashing yellow arrow lets you turn after you yield to pedestrians and oncoming traffic. A green arrow gives you the right of way. Yellow lines separate opposite directions. A solid yellow line on your side means no passing. Double solid yellow means no passing either way. White lines separate lanes going the same way. Crossing a double solid white line is not allowed. Never use a two-way left turn lane to travel. Red lanes are transit only.

Handbook: Traffic Signals and Pavement Markings

7 practice questions

1. A traffic signal is dark because of a power outage. How should you treat the intersection?
  1. Wait for the power to return before moving
  2. Go straight through but do not turn
  3. Treat it as a yield sign and go if no one is close
  4. Stop as if there were stop signs in all directions
Show answer

Answer: D. Stop as if there were stop signs in all directions

A dark signal is treated like a stop sign in every direction. Each driver stops, then proceeds when it is the driver's turn.

Handbook: Traffic Signals (p. 15)

2. You face a flashing yellow arrow pointing left. What must you do before you turn?
  1. Yield to pedestrians and oncoming traffic
  2. Stop only if a police officer is present
  3. Turn first because oncoming traffic must stop
  4. Stop and wait for a green arrow
Show answer

Answer: A. Yield to pedestrians and oncoming traffic

A flashing yellow arrow lets you make the turn, but only after you yield to pedestrians and oncoming traffic. Oncoming traffic has a steady green signal.

Handbook: Traffic Signals – Flashing Yellow Arrow (p. 16)

3. A steady yellow light comes on as you approach an intersection. What should you do?
  1. Stop immediately, even in the middle of the intersection
  2. Stop before entering if you can, or drive through carefully if you cannot stop safely
  3. Treat it the same as a flashing yellow light
  4. Speed up and clear the intersection before the light turns red, even if you must go over the limit
Show answer

Answer: B. Stop before entering if you can, or drive through carefully if you cannot stop safely

A steady yellow warns that the light is about to turn red. Stop if you can do so safely, and do not speed up to beat the light.

Handbook: Traffic Signals – Steady Circular Yellow (p. 15)

4. The center of a two-lane road has a solid yellow line on your side and a broken yellow line on the other side. What does it mean?
  1. Neither driver may pass
  2. Both drivers may pass with care
  3. You may not pass, but oncoming drivers may pass
  4. You may pass, but the oncoming drivers may not pass
Show answer

Answer: C. You may not pass, but oncoming drivers may pass

A solid line on your side of the center line means no passing for you. The broken line on the other side means those drivers may pass.

Handbook: Pavement Markings (p. 22)

5. A center lane is marked as a two-way special left turn lane. How should you use it?
  1. Drive in it for a short way to pass slower traffic on the road ahead
  2. Use it to merge into traffic from a driveway at speed
  3. Drive in it for a block to get ahead of traffic
  4. Enter it just before your turn and wait there for traffic to clear
Show answer

Answer: D. Enter it just before your turn and wait there for traffic to clear

It is illegal to travel in a two-way left turn lane. Enter it just before the turn and wait in it until you can complete the turn.

Handbook: Pavement Markings – Two-way special left turn lane (p. 23)

6. What does a flashing red signal mean?
  1. The same as a stop sign
  2. Stop only if other cars are close
  3. The signal is broken and you may ignore it
  4. Slow down and proceed with caution
Show answer

Answer: A. The same as a stop sign

A flashing red or dark signal is treated like a stop sign. Come to a full stop and go when it is your turn.

Handbook: Traffic Signals – Flashing Red or Dark Signal (p. 15)

7. You approach a freeway on-ramp where the ramp meter is dark. What should you do?
  1. Wait for another car to go first
  2. Do not stop at it; proceed and merge
  3. Treat it as a stop sign
  4. Stop and wait for it to turn green first
Show answer

Answer: B. Do not stop at it; proceed and merge

Ramp meters work only at certain times of day. A dark meter is not in use, so do not stop at it.

Handbook: Freeway Driving – Entering a Freeway (p. 35)